Big step for me yesterday: Trying for the first time to build an amp (with 6J1 & 6P1 tubes) from scratch
🧐 Wish me luck!- 1.jpg (68.5 KiB) Viewed 2549 times
- 4.jpg (83.32 KiB) Viewed 2549 times
- 6.jpg (82.73 KiB) Viewed 2549 times
New DIY Tube Amplifier Project
New DIY Tube Amplifier Project
Hi All,
Big step for me yesterday: Trying for the first time to build an amp (with 6J1 & 6P1 tubes) from scratch🧐 Wish me luck!
Big step for me yesterday: Trying for the first time to build an amp (with 6J1 & 6P1 tubes) from scratch
🧐 Wish me luck!
Last edited by sdiesel77 on Fri Dec 07, 2018 11:35 am, edited 1 time in total.
Tubes & Vinyls are making life brighter..
Re: New DIY Tube Amplifier Project
- 12.jpg (106.87 KiB) Viewed 2547 times
- 15.jpg (78.84 KiB) Viewed 2547 times
Tubes & Vinyls are making life brighter..
-
Ken Moreland
- Posts: 814
- Joined: Sun Jan 17, 2010 7:47 pm
Re: New DIY Tube Amplifier Project
Good luck.
i5 QuietPC , JplayFemto , Singxer SU-6 , Holo Audio Spring DAC ,LAB12 Preamp, Roundtree Mono Amps, Rosso Fiorentino Elba 2 Speakers
.
.
Re: New DIY Tube Amplifier Project
good stuff, best of luck
nige
nige
sd card player, modded soekris dac, class a lifepo4 amp or gb class a/b amp, diy open baffle speakers based on project audio mundorf trio 10's
Re: New DIY Tube Amplifier Project
Good man!
Just watch the HV -we need all the solder slingers we have!
Just watch the HV -we need all the solder slingers we have!
Do or do not, there is no try
Re: New DIY Tube Amplifier Project
Nice work.
One small point: the heater supply is AC and the cabling needs to be as far away as possible to the signal cables. In your pic above, I would get those 'blue' twisted cables into the angle at the back of the chassis and keep them there with a spot of glue. The gain structure might be different for a guitar amp but most guitar amps, the point to point wired ones, keep the heater wiring well out of the way.
Neat work, looking forward to the build.
One small point: the heater supply is AC and the cabling needs to be as far away as possible to the signal cables. In your pic above, I would get those 'blue' twisted cables into the angle at the back of the chassis and keep them there with a spot of glue. The gain structure might be different for a guitar amp but most guitar amps, the point to point wired ones, keep the heater wiring well out of the way.
Neat work, looking forward to the build.
It's OK, if there is no bread I will eat cake.
Beware of a thin chef!
Beware of a thin chef!
Re: New DIY Tube Amplifier Project
Good stuff and good luck. I have a friend building a tube amp at the moment (though he has been at it for the last few years :-) ) - I'll show him your progress to try get him energized
Probably not accessible to most of the forum members but came across this from a recent Stereophile article - looks very interesting for DIY amp builders http://www.burningamp.org
Probably not accessible to most of the forum members but came across this from a recent Stereophile article - looks very interesting for DIY amp builders http://www.burningamp.org
SonicTransporter Optical i9, Roon, opticalRendu, Sonore Signare LPSU, Chord DAVE, Merrill Audio Element 116 Monoblocs, Wilson Audio Sasha 2
Re: RE: Re: New DIY Tube Amplifier Project
That's a fair point. Was thinking about it but at the time I didn't have enough wire length to do it this way.Rocker wrote:Nice work.
One small point: the heater supply is AC and the cabling needs to be as far away as possible to the signal cables. In your pic above, I would get those 'blue' twisted cables into the angle at the back of the chassis and keep them there with a spot of glue. The gain structure might be different for a guitar amp but most guitar amps, the point to point wired ones, keep the heater wiring well out of the way.
Neat work, looking forward to the build.
I'll try the amp like this (should be ok) and if a hum, I'll rewire the heater [emoji39]
Tubes & Vinyls are making life brighter..