Tír Na HiFi

minionas wrote:....
A bit offtopic: my haswell does not handle AVX2 MQN versions (dos boxes stay, no errors, but also no sound) or the problem is somewhere else... <-- ANYONE WITH SOME HELP OR IDEAS :)?

Aleg wrote: Minionas

Are you still able to check the Windows Event Viewer or have you reduced the services of the Windows OS with AudiophileOptimiser or something like that?

In my experience not running AVX2 while the DOS Box remains open is due to autorisation issues.
In Event Viewer under Applications, you will see that mqnplay.exe has crashed with Exception code 0xc0000005. This is an indication of insufficient autorisation.

Try these settings:
- set the checkbox "Run this program as an Administrator" on both mqncontrol.exe and mqnplay1644.exe. You do this by right-click on those files and select Properties. On the second tab called Compatibility, click the checkbox "Run this program as an Administrator" and click OK.

- also try to make a new directory in c:\ and download the files into that new directory. Sometimes I notice Windows 'remembers' 'things' with respect to mqnplay.exe from older versions in a directory.

I can be fussy to get it running but once it does you won't want to go back.

Cheers

Aleg

adolfo.a.aguiar wrote:Unfortunately, I had no success in going picoless with Intel S1200KPR board. When booting I get two long beeps twice and then the power on led goes off. I checked all voltages in the ATX-24 connector and they are ok. It seems that the power good signal must be delayed.

Anyway, I was already considering buying the Asus H81i-plus mobo because I would like to play MQn avx2.
Nige2000, I see in your signature you are using an I3 processor. Which one? Why did you choose an I3 instead of an I7? Wouldn't an I7 give more flexibility if JPlay improves and betters MQn?

minionas wrote:I just finished a fully working picoless pc build:
MSI B85M-G43 + Haswell I5 4670T + 8GB + PPA SATA CABLED SSD OS with PPA alluminium block + PPA USB + 3M 5100S "box" covered RAM sticks + 3M 5100S sheet under motherboard.
Power supplies at the moment are:
1. Single transformer powered dual rail PPA 12V regulator:
a) - 1 x ATX;
b) - 1 x CPU;
2. Dedicated audio quality transformer powered Audiowind A-270v2 regulated 5V rail - ATX;
3. Dedicated audio quality transformer powered Audiowind A-270v2 regulated 3,3V rail - ATX;
4. Dedicated audio quality transformer powered Audiowind A-270v2 regulated 3,3V rail - PPA Clock module (upgraded "South bridge clock" on motherboard);
5. STONTRONICS single rail 5V linear to Nimh battery pack with Mundorf M-Lytic AudioGrade power cap - SSD;
6. STONTRONICS single rail 5V linear to Nimh battery pack with Mundorf M-Lytic AudioGrade power cap - PPA USB.

All on my PC is connected to single STAR GROUND point on copper bar. ALL the wiring is done with silver plated copper wires in teflon.

Closest plans:
install a LIFEPO4 3,3V cell into PPA clock rail;
install a OS USB and leave SSD for music files storage (ordered USB Sandisk 32GB flash drive and plan to power it with dedicated rail + LIFEPO4); <-- ANYONE DONE THIS WITH GOOD RESULTS COMPARING WITH OS ON SSD (interested only in W2012 server OS) ?
add LIFEPO4 on CPU and all ATX rails;
change STONTRONICS with dedicated audio quality transformer powered Audiowind A-270v2 very low noise regulators and add LIFEPO4;
to do more of 3M 5100S shielding; <-- ANY RECOMMENDATIONS OF PLACES WHERE IT MIGHT GIVE A GOOD RESULT?
to do the DC wiring noise insulation with cotton/alluminium foil combo.

Before going picoless, had a same system just with PPA 12V pico and without no. 2, 3 and 4 power supplies and without STAR GROUND. Going picoless and doing a STAR GROUND brought me lower noise floor and stronger bass, which was apparently noticeable since first seconds of my test tracks.

A bit offtopic: my haswell does not handle AVX2 MQN versions (dos boxes stay, no errors, but also no sound) or the problem is somewhere else... <-- ANYONE WITH SOME HELP OR IDEAS :)?

adolfo.a.aguiar wrote:"kinda like the cheap haswell msi boards work oob, little trouble"


Nige2000,

Did you have any trouble going picoless with the h81i-plus? My case is Streacom FC8 Evo and it supports mini-ITX only.
Which I3 CPU are you using?

adolfo.a.aguiar wrote:Yes, MSI has h81 mini-ITX but the position of the ATX-24 connector makes it harder to passive cool the CPU.

minionas wrote:My mess in the process:


Transformers & regulators allum. box:


ATX Side:


Clock side:


Center:


AUDIOPC:


Not very clean still, as still some tidying-up and re-arranging to do:)